COMPANY HEADER
Request Information
  • Variable Capacitance Technology
  • 6 Degrees of Freedom Measurements
  • Hermetically Sealed
  • DC Response
  • International Traffic in Arms Regulation (ITAR) Free
Unit of Measure

Specifications

Brands

 N/A Dytran

Sensor Type

 N/A Vibration

Physical

Maximum Weight

 N/A 1.9 oz55 g

Connector Type

 N/A 5/16-32 United Extra Fine (UNEF-2A)

Material

 N/A Ti-6AI-4V

Accelerometer Performance

Accelerometer Input Range (±)

 N/A 10 g98.1 m/s²

±5 Percent Accelerometer Frequency Response

 N/A 0 to 600 Hz

Accelerometer Frequency Response at ±3 Decibel (dB) Bandwidth

 N/A 0 to 2500 Hz
Nominal Scale Factor1 N/A 235 mV/g24.0 mV/m/s²

Typical Output Noise

 N/A 0.00004 g rms/√ Hz0.0004 m/s²/√ Hz
Typical Accelerometer Full Scale (F.S.) Non-Linearity2 N/A 0.2 %

Accelerometer Temperature Range

 N/A -67 to 257 ºF-55 to 125 ºC
Scale Factor Temperature Coefficient3 N/A 67 ppm/ºF120 ppm/ºC

Maximum Axis Misalignment

 N/A 10 mrad

Shock Survivability

 N/A 6000 g58860 m/s²

Accelerometer Resonant Frequency

 N/A >2.8 kHz

Maximum Accelerometer Cross Axis Sensitivity

 N/A 5 %

Gyro Performance

Gyro Input Range (±)

 N/A 150 º/sec

Gyro Frequency Response

 N/A 1 to 3000 Hz
±10 Percent (%) Sensitivity4 N/A 12.5 mV/º/sec

Typical Noise Density Rate

 N/A 0.04 (º/sec)/√ Hz
Typical Gyro Full Scale (F.S.) Non-Linearity5 N/A 0.2 %

Gyro Temperature Range

 N/A -40 to 221 ºF-40 to 105 ºC

Gyro Resonant Frequency

 N/A 14.5 kHz

Maximum Gyro Cross Axis Sensitivity

 N/A 5 %

Electrical

Nominal Output Impedance

 N/A 2 O

Direct Current (DC) Operating Voltage

 N/A 6 to 14 V

Direct Current (DC) Operating Bias Voltage

 N/A 2.5 V

Direct Current (DC) Operating Bias Voltage Tolerance (±)

 N/A 0.5 V

Typical Operating Direct Current (DC)

 N/A 23 mA

Maximum Operating Direct Current (DC)

 N/A 28 mA

Power Supply Rejection Ratio

 N/A >65 dB

Environmental

Storage Temperature

 N/A -67 to 257 ºF-55 to 125 ºC

Environmental Seal

 N/A Hermetic

Supplied Accessories

Supplied Accessories

 N/A
  1. Accredited calibration certificate (ISO 17025)
  2. Mounting screw model 6753, 8-32 UNF-2A, qty 2
  3. Mounting washer model 6754, qty 2
  4. Mounting screw model 6687, M4 x 0.7, qty 2

Note

Note

 N/A In the interest of constant product improvement, we reserve the right to change specifications without notice. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts.
Units on the line drawing are in inches.
  • 1 Measured using Earth gravity
  • 2 Best fit zero based line method
  • 3 Over the rated temperature range
  • 4 Measured using Earth gravity
  • 5 Best fit zero based line method